Replace the screws around the edges and screw them back on tightly. To fit the door back together, first plug the wires back in making sure they're replaced in the correct formation.Ĭarefully push the two halves of the door back together and rest them back down, holding them together so the inner section doesn't pop back up. The dishwasher handle should now fit properly. Make sure the two screws are fully tightened, and then replace the control box making sure it's clipped into place. One of the screws is just on the inside of the door, and the other one is behind the control box, so you'll need to remove it by carefully pulling it out from its clips. You'll have to disconnect some of the wires to get easy access to the components, and we recommend you take a photo of the location of the wires so you know where to replace them later. Note: This video is intended to give you the general idea of the part replacement procedure.
How to replace a dishwasher handle how to#
Step by step instructions on how to replace a Dishwasher Door Latch Handle for KitchenAid KUDK03ITWH0 Door latch failure AP6012288. Be very careful to keep hold of the door as you unscrew to make sure it doesn't fall away.Ĭarefully place the front of the door down, taking care of any sharp edges especially around the inside section of the door. How to Replace Dishwasher Door Latch Handle for KitchenAid KUDK03ITWH0 Door latch failure AP6012288. Open the door fully and remove the screws from round the edge remember to put them somewhere safe so you can replace them later. To get to the screws, you'll need to dismantle the dishwasher door. If the handle on your dishwasher is loose, you'll need to tighten the screws that fix it on. IMPORTANT: BEFORE REPLACING A PART IN ANY ELECTRICAL APPLIANCE, YOU MUST ENSURE THAT THE APPLIANCE IS FIRST UNPLUGGED FROM THE MAINS.
But be careful not to split the board, as they are fragile.Video Transcript: How to Replace the Door Handle on a Dishwasher You should drill the hole near the back of the sidewall and ensure the water and power lines can reach through it. Once you’ve removed the cabinet where your new dishwasher will go, you need to make a hole for the plumbing and wiring to run through.Īs long as you placed your dishwasher right next to the sink, you should use a drill with a core bit to drill through the sidewall of the cabinet closest to the sink. This can be easily done with a wrench to make sure it fits flush with your countertop. Once the dishwasher is in place, you can adjust the height of the dishwasher legs. Be sure to use a chalk line or laser level to get the straightest line. Your cut lines must be straight, so your dishwasher can slide right in. You will need to cut into the base of the cabinet box and again use the measured dimensions of your new dishwasher. If your cabinets are not built-in, you can use a reciprocating saw or a jigsaw to cut into the face of the cabinet.ĭo this only as wide and high as your dishwasher requires. If you are installing a dishwasher for the first time, you will need to remove a cabinet to make space for it.
How to replace a dishwasher handle install#
Removing a Cabinet to Install a Dishwasher for the First Time Dishwashers, unlike refrigerators or stoves, generally come in one standard size: 24 inches wide, 35 inches high, and 24 inches deep. If you are replacing an existing dishwasher, this project will be easier. So placing it near the sink is the standard choice for most homeowners. Dishwashers use the water and waste lines connected to your sink. Let’s get started!īefore you begin this DIY project, make sure you have a functional space and placement for the dishwasher.
Even a beginner DIYer can handle this project with ease by carefully following instructions. Reciprocating or jigsaw, power drill with core bit, and chalk line or laser level (if you’re removing a cabinet to make room for a dishwasher) That’s all you need to get started.Īnd your new dishwasher, of course! Many new dishwashers will come with the installation supplies you need (like the dishwasher 90 fitting and a new supply line).īut it’s wise to grab these essentials in case yours doesn’t.
0 kommentar(er)
